Kia Cee'd: Tires/Wheels / Alignment Repair procedures

Kia Cee'd JD Service Manual / Suspension System / Tires/Wheels / Alignment Repair procedures

Front wheel alignment

When using a commercially available computerized wheel alignment equipment to inspect the front wheel alignment, always position the vehicle on a level surface with the front wheels facing straight ahead.

Prior to inspection, make sure that the front suspension and steering system are in normal operating condition and that the tires are inflated to the specified pressure.

Toe

B - A > 0: Toe in (+)

B - A < 0: Toe out (-)

Toe adjustment

1.	Loosen the tie rod end lock nut.

2.	Remove the bellows clip to prevent the bellows from being twisted.

Adjust the toe by screwing or unscrewing the tie rod. Toe adjustment should be made by turning the right and left tie rods by the same amount.

Toe-in

Total : 0.16° ± 0.2°

Individual : 0.08° ± 0.1°

When completing the toe adjustment, install the bellows clip and tighten the tie rod end lock nut to specified torque.

Tightening torque:

49.0 ~ 53.9 N.m (5.0 ~ 5.5 kgf.m, 36.2 ~ 39.8 lb-ft)

Camber and Caster

Camber and Caster are pre-set at the factory, so they do not need to be adjusted. If the camber and caster are not within the standard value, replace or repair the damaged parts and then inspect again.

Camber angle : -0.5° ± 0.5°

Caster angle : 5.2° ± 0.5°

Rear wheel alignment

When using a commercially available computerized wheel alignment equipment to inspect the rear wheel alignment, always position the vehicle on a level surface.

Prior to inspection, make sure that the rear suspension system is in normal operating condition and that the tires are inflated to the specified pressure.

Toe

B - A > 0: Toe in (+)

B - A < 0: Toe out (-)

Toe adjustment

1.	Loosen the nut holding the assist arm cam bolt (A).

Adjust rear toe by turning the rear assist arm cam bolt (A) clockwise or counter clockwise. Toe adjustment should be made by turning the right and left cam bolt by the same amount.

Toe-in

Total : 0.14° ± 0.2°

0.06° ± 0.2° (Only "T-GDI")

Individual : 0.07° ± 0.1°

0.03° ± 0.1° (Only "T-GDI")

When completing the toe adjustment, tighten the nut to specified torque.

Tightening torque:

98.1 ~ 117.7Nm (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)

Camber

Camber is pre-set at the factory, so it does not need to be adjusted. If the camber is not within the standard value, replace or repair the damaged parts and then inspect again.

Camber : -1.0° ± 0.5°

Wheel Repair procedures

Hub nut tightening sequence Tighten the hub nuts as follows. Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft) ...

Tire Pressure Monitoring System

...

Other information:

Kia Cee'd JD Owners Manual: Windshield wipers (front)
Operates as follows when the ignition switch is turned ON. : For a single wiping cycle, move the lever to this position and release it. The wipers will operate continuously if the lever is held in this position. O : Wiper is not in operation --- :Wiper operates intermittently at the s ...

Kia Cee'd JD Service Manual: Adaptive Front Lighting System Description and operation
Description AFLS Unit(ECU) AFLS located in Cockpit Module is provided information of vehicle (steering wheel signal,vehicle speed, inclination of vehicle). Based on provided information , it calculates algorithm and adjust Low beam of H/Lamp. It transmits driving ...