Kia Cee'd: Timing System / Drive Belt Repair procedures

Removal
1.
Disconnect the battery negative terminal.
2.
Loosen the alternator tension adjusting bolt (A) to loosen tension.

3.
Remove the drive belt (A).

Inspection
Drive Belt Inspection
Visually check the belt for excessive wear, frayed cords etc.
If any defect has been found, replace the drive belt.
  
Cracks on the rib side of a belt are considered acceptable. If the belt has chunks missing from the ribs, it should be replaced.

Adjustment
Drive belt tension measurement and adjustment
Belt tension measurement
Measure the belt tension using a mechanical tension gauge or a sonic tension meter.
Tension
New belt: 686.5 ~ 784.5N (70 ~ 80kg, 154.3 ~ 176.4lb)
Used belt: 490.3 ~ 588.4N (50 ~ 60kg, 110.2 ~ 132.3lb)
  
If the engine has run for 5 minutes or more, the belt tension must be adjusted as a used belt.
When installing the V-ribbed belt, all grooves on the pulley should be covered with belt ribs.
A loose belt causes slip noise.
Too tight belt cause bearing of alternator and water pump to damage.
Using a mechanical tension gauge
1.
While pressing the handle (A) of the gauge, insert the belt (B) between pulley and pulley (or idler) into the gap between spindle (C) and hook (D).

2.
After releasing the handle (A), read a value on the dial pointed by the indicator (B).

Using a sonic tension meter
1.
Input the belt specifications into the tension meter.
 
Belt type
Location of measurement
Input data
M (Mass, g/m.rib)
W (Width, rib)
S (Span, mm)
With A/C
Crankshaft pulley to A/C compressor pulley 
13.4
6
178.9
Without A/C
Idler to alternator pulley
13.4
6
Actual measurement value

  
Measurement of S (Span) : Caculate average value after measuring the distance 3~4 times.

D : Idlerd
d : Alternator pulley

2.
Locate the micro phone (B) close to the center of belt span (A) and bounce the belt by finger 2~3 times. Read a value on the display.
[With A/C]

[Without A/C]

If adjustment is necessary:
1.
Loosen the mounting bolts (A).
2.
Tighten the adjusting bolt(B) clockwise in loose tension ; loosen the bolt counterclockwise in high tension.

3.
Recheck tension of the belt.
4.
After adjusting tension, tighten the through bolts.
Tightening torque
12mm (0.47in) bolt :
19.6 ~ 26.5 Nm (2.0 ~ 2.7 kgf.m, 14.5 ~ 19.5 Ib-ft)
14mm (0.55in) bolt :
29.4 ~ 41.2 Nm (3.0 ~ 4.2 kgf.m, 21.7 ~ 30.4 Ib-ft)
Installation
1.
Install the drive belt (A).

2.
Adjust tension by tightening the alternator tension adjust bolt (B) and then install the mounting bilts(A).
Tightening torque
12mm (0.47in) bolt :
19.6 ~ 26.5 Nm (2.0 ~ 2.7 kgf.m, 14.5 ~ 19.5 Ib-ft)
14mm (0.55in) bolt :
29.4 ~ 41.2 Nm (3.0 ~ 4.2 kgf.m, 21.7 ~ 30.4 Ib-ft)

3.
Connect the battery negative terminal.
Drive Belt Components and components location
Components   1. Drive belt ...

Idler Components and components location
Components   1. Idler ...

Other information:

Kia Cee'd JD Owners Manual: Headlamp welcome
When the headlight(light switch in the headlight or AUTO position) is on and all doors (and tailgate) are locked and closed, the headlight, position light and tail light will come on for 15 seconds if any of the below is performed. Without smart key system - When the door unlock butt ...

Kia Cee'd JD Service Manual: Troubleshooting
Engine Overheat Troubleshooting   Inspection Remedy Visual inspection Inspect for shortage of coolant in reservoir tank . Reinspect after replenishing coolant. Inspect for coolant pollution after ...

© 2017-2025 www.kceed.com