Kia Cee'd: Front Suspension System / Front Strut Assembly Repair procedures

Kia Cee'd JD Service Manual / Suspension System / Front Suspension System / Front Strut Assembly Repair procedures

Replacement
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from front hub.
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

  
•
Be careful not to damage to the hub bolts when removing the rear wheel and tire (A).
3.
Remove the wheel speed sensor (A) bracket from the front strut assembly by loosening the mounting bolts (B).
Tightening torque :
6.8 ~ 10.7 N.m(0.7 ~ 1.1 kgf.m, 5.0 ~ 7.9 lb-ft)

4.
Disconnect the stabilizer link (B) from the front strut assembly (A) after loosening the nut.
Tightening torque:
98.1 ~ 117.7N.m(10.0 ~ 12.0kgf.m, 72.3~86.8lb-ft)

5.
Remove the cowl top cover (A).
(Refer to Brake System - "Front Disc Brake")

6.
Remove the front strut assembly and then loosen the strut mounting nuts (A).
Tightening torque:
44.1 ~ 58.8N.m(4.5 ~ 6.0kgf.m, 32.5~43.4lb-ft)

7.
Disconnect the front strut assembly (A) from the knuckle by loosening the bolt & nut.
Tightening torque:
137.3 ~ 156.9N.m(14.0 ~ 16.0kgf.m, 101.3 ~ 115.7lb-ft)

8.
Install in the reverse order of removal.
Disassembly
1.
Using the special tool (09546-26000), compress the coil spring (A).
Tightening torque:
58.8 ~ 73.5 N.m(6.0 ~ 7.5 kgf.m, 43.4 ~ 54.2 lb-ft)

2.
Remove the self-locking nut (C) from the strut assembly (B).
3.
Remove the insulator, spring seat, coil spring and dust cover from the strut assembly.
4.
Reassembly is the reverse of the disassembly.
Inspection
1.
Check the strut bearing for wear and damage.
2.
Check the spring upper and lower seat for damage and deterioration.
3.
Compress and extend the piston rod (A) and check that there is no abnormal resistance or unusual sound during operation.

Disposal
1.
Fully extend the piston rod.
2.
Drill a hole on the (A) section to remove gas from the cylinder.

  
•
The gas coming out is harmless but be careful of chips that may tly when driling.
Front Strut Assembly Components and components location
Components   1. Strut assembly 2. Insulator 3. Strut bearing 4. Spring upper pad 5. Coil spring 6. Dust cover 7. Spring lower pad ...

Front Lower Arm Repair procedures
Replacement 1. Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. 2. Remove the front w ...

Other information:

Kia Cee'd JD Service Manual: Repair procedures
Inspection Lighting Switch Inspection With the multifunction switch in each position, make sure that continuity exists between the terminals below. If continuity is not as specified, replace the multi-function switch. Lighting Switch (Auto Light) Lighting S ...

Kia Cee'd JD Service Manual: Specifications
Specification   Item Specification Ultrasonic sensor Voltage rating DC 12 V Detecting range 30 cm ~ 120 cm Operation voltage DC 9 ~ 16 V ...

© 2017-2025 www.kceed.com