Kia Cee'd: Windshield Wiper/Washer / Front Washer Motor Repair procedures

Kia Cee'd JD Service Manual / Body Electrical System / Windshield Wiper/Washer / Front Washer Motor Repair procedures

Inspection

Front and Rear Washer Motor

With the washer motor connected to the reservoir tank, fill the reservoir tank with water.

Before filling the reservoir tank with water, check the filter for foreign material or contamination. if necessary, clean the filter.

2.	Connect positive (+) battery cables to terminal 1 and negative (-) battery cables to terminal 2 respectively.

3.	Check that the motor operates normally and the washer motor runs and water sprays from the front nozzles.

If they are abnormal, replace the washer motor.

[Front & Rear washer]

No.	Description
1	Windshield washer (+)
2	Ground
3	Rear washer (+)

Washer Fluid Level Sensor Switch

1.	Disconnect the negative(-) battery terminal.

2.	Drain the washer fluid less than 600 cc.

3.	Check for continuity between the No. 1 and No.2 terminal in each float position. There should be continuity when the float is down. There should be no continuity when the float is up.

If the continuity is not as specified, replace the washer fluid level switch

Reservoir tank capacity: MIN. 4.5 Liters

Head Lamp Washer Motor

With the washer motor connected to the reservoir tank, fill the reservoir tank with water.

Before filling the reservoir tank with water, check the filter for foreign material or contamination. if necessary, clean the filter.

2.	Connect positive (-) battery cables to terminal 2 and negative (+) battery cables to terminal 1 respectively.

3.	Check that the motor operates normally and the washer motor runs and water sprays from the head lamp washer nozzles.

4.	If they are abnormal, replace the head lamp washer motor.

Removal

–	When servicing the washer pump, be careful not to damage the washer pump seal.

–	Do not operate the washer pump before filling the washer reservoir. Failure to do so could result in premature pump failure.

1.	Disconnect the negative (-) battery terminal.

2.	Remove the head lamp washer nozzle cover (A).

3.	Remove the front bumper cover. (Refer to Body - "Front Bumper Cover")

4.	Remove the head lamp washer nozzle (A) after loosening bolts.

5.	Remove the washer hose and disconnect the washer motor connector (A), washer flid level sensor connector (B) and head lamp washer pump connector (C).

6.	Remove the washer motor (A) and head lamp washer pump (B).

7.	Remove the washer reservoir after removing bolts.

Installation

Reassemble the washer reservoir.

Before installing the pump motor, check the filter for foreign material or contamination. if necessary, clean the filter into the pump motor.

2.	Connect the washer motor connector and washer hose.

3.	Install the head lamp washer motor.

4.	Install the head lamp washer nozzle.

5.	Reassemble the front bumper cover.

Front Wiper Motor Repair procedures

Removal 1. Remove the cap (B) and remove the nuts, then remove the wiper arm (A). Tightening torque : 22.6 ~ 26.5 N.m(2.3 ~ ...

Rain Sensor Schematic diagrams

Circuit Diagram ...

Other information:

Kia Cee'd JD Owners Manual: Using Audio CD Mode
Playing/Pausing CD Tracks Once an audio CD is inserted, the mode will automatically start and begin playing. While playing, press the button to pause and press button to play. ✽ NOTICE Only genuine audio CDs are supported. Other discs may result in recognition failure (e.g ...

Kia Cee'd JD Service Manual: Rear Shock Absorber Components and components location
Components 1. Rear insulator cover 2. Locking nut 3. Plpe 4. Rear bracket assembly 5. Bumper rubber 6. Protector 7. Rear shock absorber assembly ...