Kia Cee'd: Windshield Wiper/Washer / Front Wiper Motor Repair procedures

Kia Cee'd JD Service Manual / Body Electrical System / Windshield Wiper/Washer / Front Wiper Motor Repair procedures

Removal

Remove the cap (B) and remove the nuts, then remove the wiper arm (A).

Tightening torque :

22.6 ~ 26.5 N.m(2.3 ~ 2.7 kgf.m, 16.6 ~ 19.5 lb-ft)

2.	If necessary, release the wiper blade fixing clip by pulling up and remove the wiper blade from the inside radius of wiper arm.

3.	Remove the weather strip and the cowl top cover (A) after removing 4 rivets.

4.	Disconnect the washer hose (B) connected to cowl top cover.

5.	Remove the windshield wiper motor and linkage assembly (A) after removing 2 bolts.

6.	Disconnect the wiper motor connector (A) from the wiper motor & linkage assembly.

7.	Hold the wiper motor crank arm and remove the upper linkage (A) from the wiper motor crank arm.

8.	Remove the lower linkage (A) from the wiper motor crank arm.

Hold the arm using the plyer, remove the crank arm (A) after loosening the mounting nut.

Before removing the wiper motor and linkage assembly, make sure that the linkage is stopped at auto stop position.

To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.

Be careful not to bend the linkage.

10.	Remove the wiper motor (A) with 3 bolts.

Installation

1.	Install the wiper motor.

Install the crank arm.

To install the wiper motor crank arm, make sure that the linkage is aligned with the crank arm in straight line and set the angle of each linkages exactly.

Install the lower and upper linkage to the wiper motor crank arm.

To install the wiper motor crank arm, make sure that the linkage is aligned with the crank arm in straight line and set the angle of each linkages exactly.

Be careful not to bend the linkage.

Install the wiper motor and linkage assembly and then connect the wiper motor connector.

Tightening torque:

6.9 ~ 10.8Nm (0.7 ~ 1.1, kgf.m, 5.0 ~ 7.9 lb-ft)

5.	Install the cowl top cover.

Install the windshield wiper arm and blade.

Tightening torque:

22.6 ~ 26.5 Nm (2.3 ~ 2.7 kgf.m, 16.6 ~ 19.5 lb-ft)

–	The windshield wiper motor must be cycled to make sure that it is in the auto stop position. If necessary, adjust the wiper arm and blade.

7.	Install the wiper arm and blade to the auto stop position. A : Auto stop position (Blade)

Inspection

Speed Operation Check

Remove the connector (A) from the wiper motor.

No.	Description	No.	Description
1	GND	4	Low
2	Parking	5	High
3	Battery	6	-

2.	Attach the positive (+) lead from the battery to terminal 3 and the negative (-) lead to terminal 1.

Check that the motor operates at low or high speed as below table.

Common sources of contamination are insects, tree sap, and hot wax treatments used by some commercial car washes. If the blades are not wiping properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.

Front Wiper Motor Components and components location

Component Location 1. Cap 2. Nut 3. Wiper arm & blade 4. Rivet 5. Cowl top cover 6. Bolt 7. Wiper motor & linkage assembly ...

Front Washer Motor Repair procedures

Inspection Front and Rear Washer Motor 1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water. ...

Other information:

Kia Cee'd JD Owners Manual: Manual heating and air conditioning
The heating and cooling system can be controlled manually by pressing buttons or turning knob(s) other than the AUTO button. In this case, the system works sequentially according to the order of buttons or knob(s) selected. 1. Start the engine. 2. Set the mode to the desired position. ...

Kia Cee'd JD Owners Manual: Easy access function
The system will move the driver's seat automatically as follows: Without smart key system - It will move the driver’s seat rearward when the ignition key is removed and front driver’s door is opened. - It will move the driver’s seat forward when the ignition key is inserted. ...