Kia Cee'd: Fuel Delivery System / High Pressure Fuel Pump Repair procedures
|
In case of removing the high pressure fuel pump, high pressure fuel
pipe, delivery pipe, and injector, there may be injury caused by leakage
of the high pressure fuel. So don’t do any repair work right after engine
stops.
|
| 1. |
Turn the ignition switch OFF and disconnect the battery negative (-)
cable.
|
| 2. |
Release the residual pressure in fuel line.
(Refer to Fuel Delivery System - “Release Residual Pressure in Fuel
Line”)
|
When removing the fuel pump relay, a Diagnostic Trouble Code
(DTC) may occur.
Delete the code with the GDS after completion of “Release Residual
Pressure in Fuel Line” work.
|
|
| 3. |
Remove the air cleaner and the air intake hose.
(Refer to Engine Mechanical System - "Intake Manifold")
|
| 4. |
Disconnect the fuel pressure regulator valve connector (A).
|
| 5. |
Disconnect the fuel feed tube quick-connector (B).
|
| 6. |
Remove the high pressure fuel pipe.
| (1) |
Remove the installation nut (A) from the high pressure fuel
pump with the special service tool [SST No.: 09314-3Q100 or
09314-27130]
|
| (2) |
Remove the installation nut (B) from the delivery pipe with
the special service tool [SST No.: 09314-3Q100 or 09314-27130]
|
| (3) |
Disconnect the engine coolant temperature sensor connector.
|
| (4) |
Remove the function block (C), and then remove the high pressure
fuel pipe.
|
|
| 7. |
Remove the installation bolts (D), and then remove the high pressure
fuel pump from the cylinder head assembly.
|
Unscrew in turn the two bolts in small step (0.5 turns). In
case of fully unscrewing one of the two bolts with the other
bolt installed, the housing surface of the cylinder head may
be broken because of tension of the pump spring.
|
|
| • |
Before installing the high pressure fuel pump, position the
roller tappet in the lowest position by rotating the crankshaft.
Otherwise the installation bolts may be broken because of tension
of the pump spring.
|
|
| • |
Be careful to be free from foreign materials when assembling.
|
|
| • |
Do not reuse the used bolt.
|
|
| • |
Do not reuse the used high pressure fuel pipe.
|
|
| • |
When tightening the installation bolts of the high pressure
fuel pump, tighten in turn the bolts in small step (0.5 turns)
after tightening them with hand-screwed torque.
|
|
| • |
Install the component with the specified torques.
|
| • |
First hand-tighten the fasteners fully until they are not fastened
any more in orderto have them inserted in place and then completely
tighten to the specified torque using a torque wrench.
If not tightening the bolts or nuts in a straight line with
the mating bolt holes or fittings, it may cause a fuelleak due
to broken threads.
|
|
| • |
Note that internal damage may occur when the component is dropped.
In this case, use it after inspecting.
|
|
| • |
Apply engine oil to the O-ring (A) of the high pressure fuel
pump, the roller tappet (B), and the protrusion (C). Also apply
engine oil to the groove on the location where the protrusion
(C) is installed.
|
|
| 1. |
Installation is reverse of removal.
|
Use the special service tool [SST No.: 09314-3Q100 or 09314-27130]
to install the high pressure fuel pipe.
|
|
High pressure fuel pump installation bolt:
12.8 ~ 14.7 N.m (1.3 ~ 1.5 kgf.m, 9.4 ~ 10.9 lb-ft)
High pressure fuel pipe installation nut:
26.5 ~ 32.4 N.m (2.7 ~ 3.3 kgf.m, 19.5 ~ 23.9 lb-ft)
High pressure fuel pipe function block installation bolt:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
|
|
Removal
In case of removing the high pressure fuel pump, high pressure fuel
pipe, delivery pipe, and inject ...
Delivery Pipe Repair procedures
Clutch System