Kia Cee'd: Clutch Cover And Disc / Repair procedures

Kia Cee'd JD Service Manual / Clutch System / Clutch Cover And Disc / Repair procedures

Removal

Remove the transaxle assembly.

G 1.6 MPI (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.4 MPI (Refer to Manual Transaxle System - " Manual Transaxle")

D 1.6 TCI-U2 (Refer to Manual Transaxle System - " Manual Transaxle")

D 1.4 TCI-U2 (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.6 GDI (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.6 T-GDI (Refer to Manual Transaxle System - " Manual Transaxle")

2.	Remove the clutch cover bolts. Be careful not to be bent or twist bolts. Loosen bolts in diagonal directions.

Inspection

1.	Inspect diaphragm spring wear which is in contact with a concentric slave cylinder bearing.

2.	Check the clutch cover and disc surface for wear or cracks.

3.	Check the clutch disc lining for slipping or oil marks.

Measure the depth from a clutch lining surface to a rivet. If the measured value is less than the specification below, replace it.

Standard value

Clutch disc rivet depth (A): 0.3 mm (0.0118 in.)

Installation

If reinstalling used cover, the cover should be installed with its clutch disc as a set.

Apply grease on a disc spline part and transaxle input shaft spline part as required.

Specified grease: CASMOLY L9508

Amount: 0.2 g

Possible problems when not following

•	When not applying: Excessive wear of splines and bad clutch operation can occur.

•	When excessively applying: Grease can be scattered by centrifugal force which can conaminate the clutch disc. This can cause a loss of friction force causing a slip.

The 'T/M SIDE' marked surface should face the transaxle.

Possible problems when the disc is installed in the opposite direction.

•	Transaxle shift error or a strange sound can occur due to clutch separation.

3.	Install the clutch disc and the cover with SST (A: 09411-1P000).

Install the clutch cover bolts. Not to be bent or twisted, Tighten them in diagonal directions.

Tightening torque:

Gasoline : 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

Diesel : 11.8 ~ 14.7 N.m (1.2 ~ 1.5 kgf.m, 8.7 ~ 10.8 lb-ft)

•	Loosely tighten every clutch cover bolts, then torque to specifications in a diagonal direction. This can prevent twisting, vibration of the cover, and the lifting of the pressure plate.

•	Install the all the components with the specified torques. If not, the clutch torque transaxle may have concerns or the mounting bolt can loosen.

Install the transaxle assembly.

G 1.6 MPI (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.4 MPI (Refer to Manual Transaxle System - " Manual Transaxle")

D 1.6 TCI-U2 (Refer to Manual Transaxle System - " Manual Transaxle")

D 1.4 TCI-U2 (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.6 GDI (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.6 T-GDI (Refer to Manual Transaxle System - " Manual Transaxle")

Components and components location

Components 1. Clutch release fork 2. Clutch cover assembly 3. Clutch disk assembly 4. Clutch release bearing ...

Clutch Switch

...

Other information:

Kia Cee'd JD Service Manual: Troubleshooting
Standard Flow of Diagnostic Troubleshooting Notes With Regard To Diagnosis The phenomena listed in the following table are not abnormal. Phenomenon Explanation System check sound When starting the engine, a thudding soun ...

Kia Cee'd JD Owners Manual: Closing the tailgate
❈ The actual luggage room in the vehicle may differ from the illustration. Lower and push down the tailgate firmly. Make sure that the tailgate is securely latched. WARNING Make sure your hands, feet and other parts of your body are safely out of the way before closing the tailgate. ...