Kia Cee'd: Ignition Lock Switch / Repair procedures
Signal Circuit Inspection
| 1. |
Check ignition lock switch pull-up voltage
| (1) |
IG KEY "OFF", ENGINE "OFF".
|
| (2) |
Disconnect ignition lock switch connector.
|
| (4) |
Measure the voltage between signal terminal of ignition lock
switch harness connector and chassis ground.
|
Specification : 11.5V ~ 13.0V
|
|
|
| 2. |
Check open in ignition lock switch signal circuit
| (1) |
IG KEY "OFF", ENGINE "OFF".
|
| (2) |
Disconnect ignition lock switch connector and ECM connector.
|
| (3) |
Check continuity between signal terminal of lock switch signal
harness connector and ECM harness connector.
|
Specification : Continuity ( below 1.0Ω )
|
|
|
Ground Circuit inspection
| 1. |
IG KEY "OFF", ENGINE "OFF".
|
| 2. |
Disconnect ignition lock switch connector.
|
| 3. |
Check continuity between lock switch signal connector terminal 1 and
chassis ground.
|
Specification : Continuity ( below 1.0Ω )
|
|
Component Inspection
| 1. |
Remove the ignition lock switch.
|
| 2. |
Push the ignition lock switch in the direction of the arrow to make
sure that continuity between terminals. (refer to the table below)
|
Standard value :
Full stroke (A): 12.0 ± 0.3mm (0.4724 ± 0.0118 in.)
ON-OFF point (B): 2.0 mm(0.0787 in.)
|
|
Condition
|
Clutch Pedal pressed
|
Clutch Pedal Released
|
Switch Operation
|
ON (below 1.0Ω )
|
OFF ( Infinite Ω )
|
|
|
| 1. |
Turn ignition switch OFF and disconnect the negative (-) battery cable.
|
| 2. |
Disconnect ignition lock switch connector (A).
|
| 3. |
Remove the ignition lock switch by loosening a nut (A).
|
| 1. |
Install in the reverse order of removal.
|
| 2. |
Adjust the ignition switch.
| (1) |
In state of full stroke, adjust the gab by rotating the adjust
nut (A) to satisfy the standard gap range.
|
Standard gap range :
Gasoline : 3 ~ 4 mm (0.1181 ~ 0.1575 in.)
Diesel : 1 ~ 2 mm (0.0394 ~ 0.0787 in.)
|
|
| (2) |
Tighten the nut (B) with the specified torque.
|
Tightening torque:
7.8 ~ 9.8 N (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)
|
|
|
Specifications
Item
Specifications
Working voltage
DC
12V
Operating force
14.7 ± ...
Components
1. Master cylinder
2. Ignition lock switch
3. Clutch switch
4. Pedal pad
...
Other information:
Kia Cee'd JD Owners Manual: Driving information mode
This mode indicates 3 kinds of driving
Information.
All stored driving information (except
odometer, distance to empty and instant
fuel economy) resets if the battery is disconnected.
1. Distance to empty (km or mi.)
This mode indicates the estimated distance
the vehicle can be driven w ...
Kia Cee'd JD Owners Manual: Service mode
This mode calculates when you need a
scheduled maintenance service (mileage
or days)
If you want to see the service mode when
other modes are displayed, press the
button less than 1 second.
If you do not have your vehicle serviced
according to the scheduled maintenance
service on ...
Specifications
Clutch Pedal Components and components location