Kia Cee'd: Smart Key System / Smart Key Unit Repair procedures
Kia Cee'd JD Service Manual / Body Electrical System / Smart Key System / Smart Key Unit Repair procedures
| Inspection |
Smart Key Unit
| – |
Refer to Smart key system - "Smart key Diagnostic"
|
Smart Key Switch
| – |
Refer to Smart key system - "Smart key Diagnostic"
|
Antenna
| – |
Refer to Smart key system - "Smart key Diagnostic"
|
Tailgate Open Switch
| 1. |
Check for continuity between the trunk/tailgate lid open switch terminals.
|
| 2. |
If continuity is not specified, inspect the switch
|
| Removal |
Smart Key Unit
| 1. |
Disconnect the negative (-) battery terminal.
|
| 2. |
Remove the glove box housing.
(Refer to Body - "Glove Box Housing")
|
| 3. |
Remove the smart key unit (A) with loosening nuts and screw, then disconnect
the connector.
|
Interior #1 Antenna
Take care not to scratch the crash pad and related parts.
|
| 1. |
Disconnect the negative (-) battery terminal.
|
| 2. |
Remove the crash pad center lower panel.
(Refer to Body - "Main Crash Pad Assembly")
|
| 3. |
Disconnect the connector, then remove the interior #1 antenna (A) after
loosening 2 screws.
|
Interior #2 Antenna
Take care not to scratch the crash pad and related parts.
|
| 1. |
Disconnect the negative (-) battery terminal.
|
| 2. |
Remove the floor console assembly.
(Refer to Body - "Floor Console Assembly")
|
| 3. |
Disconnect the connector, then remove the interior #2 antenna (A) with
loosening 2 screws.
|
Trunk/Tailgate Antenna
| 1. |
Disconnect the negative (-) battery terminal.
|
| 2. |
Remove the rear transverse trim.
(Refer to Body - "Rear Transverse Trim")
|
| 3. |
Disconnect the connector, then remove the trunk/tailgate antenna (A)
with loosening 2 nuts.
|
Exterior Bumper Antenna
| 1. |
Disconnect the negative (-) battery terminal.
|
| 2. |
Remove the rear bumper beam assembly.
(Refer to Body - "Rear Bumper Beam Assembly")
|
| 3. |
Disconnect the connector, then remove the rear bumper antenna (A) with
loosening 2 screws.
|
Buzzer
| 1. |
Disconnect the negative (-) battery terminal.
|
| 2. |
Remove the front left head lamp.
(Refer to Lighting System - "Head Lamps")
|
| 3. |
Remove the buzzer (A) after disconnecting the connector.
|
Door Outside Handle
| 1. |
Disconnect the negative (-) battery terminal.
|
| 2. |
Loosen the mounting bolt after removing the holl pulg (B).
|
| 3. |
Remove the front door outside hand cover (A).
|
| 4. |
Remove the front door outside handle (A) by sliding it rearward.
|
| 5. |
Disconnect the front door outside handle connector (A).
|
Tailgate Open Switch
| 1. |
Disconnect the negative (-) battery terminal.
|
| 2. |
Remove the guide panel (A) after loosening the screws.
|
| 3. |
Disconnect the tailgate open switch connector (A) after loosening the
screws.
|
| Installation |
Smart Key Unit
| 1. |
Install the smart key unit.
|
| 2. |
Connect the connector and install the smart key unit.
|
| 3. |
Install the glove box housing.
|
| 4. |
Install the negative (-) battery terminal and check the smart key system.
|
Interior #1 Antenna
| 1. |
Install the interior #1 antenna.
|
| 2. |
Install the crash pad center lower panel.
|
| 3. |
Install the negative (-) battery terminal and check the smart key system.
|
Interior #2 Antenna
| 1. |
Install the interior #2 antenna.
|
| 2. |
Install the floor console assembly.
|
| 3. |
Install the negative (-) battery terminal and check the smart key system.
|
Trunk/Tailgate Antenna
| 1. |
Install the trunk/tailgate antenna.
|
| 2. |
Install the rear transverse trim.
|
| 3. |
Install the negative (-) battery terminal and check the smart key system.
|
Exterior Bumper Antenna
| 1. |
Install the exterior bumper antenna.
|
| 2. |
Install the rear bumper beam and bumper.
|
| 3. |
Install the negative (-) battery terminal and check the smart key system.
|
Buzzer
| 1. |
Install the buzzer.
|
| 2. |
Install the front left head lamp.
|
| 3. |
Install the negative (-) battery terminal and check the smart key system.
|
Door Outside Handle
| 1. |
Install the door outside handle.
|
| 2. |
Install the door trim.
|
| 3. |
Install the negative (-) battery terminal and check the smart key system.
|
Trunk/Tailgate Open Switch
| 1. |
Install the tailgate open switch.
|
| 2. |
Install the guide panel.
|
| 3. |
Install the negative (-) battery terminal and check the smart key system.
|
Smart Key Unit Schematic diagrams
Circuit Diagram
...
Other information:
Kia Cee'd JD Service Manual: Rear Pillar Trim Repair procedures
Replacement
[5Door]
•
Put on gloves to protect your hands.
•
...
Kia Cee'd JD Service Manual: Components and components location
Component Location
1. Rear glass defogger switch
(A/C controller)
2. Rear glass defogger
3. Rear glass defogger relay
...
© 2017-2024 www.kceed.com
