Kia Cee'd: Lubrication System / Engine Oil Repair procedures
| • |
Prolonged and repeated contact with mineral oil will result
in the removal of natural fats from the skin, leading to dryness,
irritation and dermatitis. In addition, used engine oil contains
potentially harmful contaminants which may cause skin cancer.
|
| • |
Exercise caution in order to minimize the length and frequency
of contact of your skin to used oil. Wear protective clothing
and gloves. Wash your skin thoroughly with soap and water, or
use water-less hand cleaner, to remove any used engine oil.
Do not use gasoline, thinners, or solvents.
|
| • |
In order to preserve the environment, used oil and used oil
filter must be disposed of only at designated disposal sites.
|
|
| 1. |
Drain engine oil.
| (1) |
Remove the oil filler cap.
|
| (2) |
Remove the oil drain plug, and drain the oil into a container.
|
|
| 2. |
Remove the oil filter(A) with the SST(09263-2E000, the oil filter wrench).
| (1) |
Remove the oil filter.
|
| (2) |
Check and clean the oil filter installation surface.
|
| (3) |
Check the part number of the new oil filter is as same as old
one.
|
| (4) |
Apply clean engine oil to the gasket of a new oil filter.
|
| (5) |
Lightly screw the oil filter into place, and tighten it until
the gasket contacts the seat.
|
| (6) |
Tighten it with the torque below.
|
Tightening torque :
11.8 ~ 15.7N.m (1.2 ~ 1.6kgf.m, 8.7 ~ 11.6lb-ft)
|
|
|
| 3. |
Refill with engine oil.
| (1) |
Clean and install the oil drain plug with a new gasket.
|
Tightening torque :
34.3 ~ 44.1N.m (3.5 ~ 4.5kgf.m, 25.3 ~ 32.5lb-ft)
|
|
| (2) |
Fill with fresh engine oil.
|
Capacity
Total : 4.0L (4.22 U.S.qt., 3.51 lmp.qt., 1.05 U.S.gal.)
Oil pan : 3.3L (3.48 U.S.qt., 2.90 lmp.qt., 0.87 U.S.gal.)
Drain and refill in cluding oil filter :
3.6L (3.80 U.S.qt., 3.16 lmp.qt., 0.95 U.S.gal.)
|
|
| (3) |
Install the oil filler cap.
|
|
| 4. |
Start engine and check for oil leaks.
|
| 5. |
Recheck the engine oil level.
|
Engine Oil
| 1. |
Check the engine oil quality.
Check the oil deterioration, entry of water, discoloring of thinning.
If the quality is visibly poor, replace the oil.
|
| 2. |
Check the engine oil level.
After warning up the engine and then 5 minutes after the engine stop,
oil level should be between the "L" and "F" marks in the dipstick.
If low, check for leakage and add oil up to the "F" mark.
|
Do not fill with engine oil above the "F" mark.
|
|
Selection Of Engine Oil
Recommendation
If not available, refer to the recommended ACEA, API or ILSAC classification
and SAE viscosity number.
Classification
| – |
ILSAC GF-E, GF-4 or above
|
SAE viscosity grade
|
For best performance and maximum protection of all types of operation,
select only those lubricants which :
| 1) |
Satisfy the requirement of the ACEA, API or ILSAC classification.
|
| 2) |
Have proper SAE grade number for expected ambient temperature
range.
|
| 3) |
Lubricants that do not have both an SAE grade number and ACEA,
API or ILSAC service classification on the container should
not be used.
|
|
Components
1.
Timing chain cover
2. Inner rotor
3.
Outer rotor
4. Pump cover
...
Oil Pump Components and components location